Subscribe to Techwave Spotlight
Stay updated on tech trends, product launches and exclusive offers! Read our Policy Policy.
Cel-Fi GO G41, GO G51 and ROAM R41 compared for Australia: which to choose, antenna layouts, cable and connector picks, and the carrier permission rule.
Three Cel-Fi repeaters cover most Australian homes, small sites and vehicles, and each does a different job. The GO G41 is the fixed unit for 4G: it relays two channels of up to 20 MHz each. The GO G51 is the fixed unit for sites that can see the carrier's 3.5 GHz 5G: it relays one 5G channel up to 100 MHz wide and one 4G channel. The ROAM R41 is the 12 V unit for vehicles and boats. All three serve one carrier at a time, and all three need that carrier's written permission before they are switched on.
No 3.5 GHz 5G at your roof: choose the G41. 3.5 GHz 5G at your roof: choose the G51. Wheels or a hull: choose the R41.
This guide is about choosing. It compares the three units, explains when the G41 is the better choice than the G51, sets out what a ROAM R41 can and cannot do away from a vehicle, and matches units and packs to sites and vehicles. Fitting them is covered in our Cel-Fi installation guide, which has the antenna, cable, splitter and combiner detail and worked designs.
The figures are from Nextivity's current datasheets for the GO G41, Rev26-1006, the GO G51, Rev26-0909 and the ROAM R41, Rev26-0909. A band is a numbered slice of spectrum defined by the 3GPP standards body. A relay channel is the part of a band the unit amplifies at one time. dBm is power relative to one milliwatt, so 0 dBm is 1 mW, 20 dBm is 100 mW and 27 dBm is 500 mW.
Cel-Fi GO G41Fixed sites on 4G, two channels
Cel-Fi GO G51Fixed sites with 3.5 GHz 5G
Cel-Fi ROAM R41Vehicles and boats, 12 V
Pictures: Nextivity. Each card opens the pack on the Techwave Store.
| Cel-Fi GO G41 | Cel-Fi GO G51 | Cel-Fi ROAM R41 | |
|---|---|---|---|
| Where it is used | Fixed, in a building | Fixed, in a building | Cars, trucks, RVs and boats |
| Bands in the Australian kit | G41-JE: 1, 3, 5, 7, 8, 28L, 40. G41-NE: 1, 3, 5, 7, 28U, 40 | G51-LE: n78 and 1, 3, 5, 7, 8, 28L | R41-YB: 1, 3, 5, 7, 8, 26, 28L |
| Channels relayed at once | 2, each up to 20 MHz | 1 on band n78 up to 100 MHz, plus 1 on a 4G band up to 20 MHz | 1, up to 20 MHz |
| 3.5 GHz 5G (band n78) | No | Yes | No |
| Carriers served at once | 1 | 1 | 1 |
| System gain | 100 dB max. | 100 dB max. | 100 dB max. |
| Downlink output power | 20 dBm max. | 20 dBm max. on the 4G bands, 27 dBm max. on n78 | 0 dBm max. |
| Uplink output power | 20 to 22 dBm max. by band | 20 to 24 dBm max. by band | 22 to 24 dBm max. by band |
| Antenna ports | SMA female, donor and server | SMA female, donor and server | SMA female, donor and server |
| Power | AC adapter to a 12 V DC input, 30 W max. | AC adapter, 60 W max. | Vehicle socket, 11.5 to 15 V DC, 18 W max. |
| Enclosure and temperature | IPX0, indoor only, 0 to 40 °C | IPX0, indoor only, 0 to 40 °C | IPX0, 0 to 60 °C |
| Setup and monitoring | WAVE App over Bluetooth, WAVE Portal over Ethernet | WAVE App over Bluetooth, WAVE Portal over Ethernet | WAVE App over Bluetooth |
| Size and weight | 267 x 107 x 56 mm, 1.0 kg | 265 x 172 x 69 mm, 2.2 kg | 170 x 79 x 43 mm, 0.49 kg |
| On the Techwave Store | G41 packs for Telstra and Optus, G41 packs for Vodafone | G51 packs | ROAM R41 packs with RFI antennas |
The band row is why the G41 comes in two Australian variants. The 700 MHz band 28 is split into a lower block, 28L, and an upper block, 28U. The JE variant can be switched to any of the Australian networks but has no band 28 for Vodafone, and the NE variant is the Vodafone unit with band 28. The G51-LE and R41-YB kits cover 28L only. Whichever unit you buy, it serves one carrier at a time, so a site that needs two carriers needs two units.
All three datasheets also list 3G, which no longer matters here: the ACMA's 3G switch-off page records that Vodafone had already closed its 3G network and that Telstra and Optus planned to close theirs from 28 October 2024.
On coverage, Nextivity's current datasheets give no floor area. An earlier G41 datasheet gave up to 3,000 m² per system. A more useful planning figure is the radius of the coverage bubble around one server antenna: about 20 m through timber-framed walls, less through concrete, and more than 65 m in an open commercial space. Treat all of these as estimates; the signal at the donor antenna and the building decide the result.
The G51 is the newer and larger unit, but it is not a G41 with 5G added. Its two relay channels are different things. One is the n78 channel, up to 100 MHz wide. The other is a single 4G channel of up to 20 MHz. The G51 datasheet gives the relay bandwidth as 100 MHz plus 20 MHz: band n78 plus one of the 4G bands. The G41's two channels are both 4G-band channels of up to 20 MHz each, 40 MHz in total.
That decides the choice at any site where the carrier's 3.5 GHz signal does not reach the donor antenna. There the G51 has one 20 MHz channel to offer and the G41 has two. Carriers routinely serve a phone on two bands at once, for example a 700 MHz channel for reach and an 1,800 MHz channel for capacity, and a G41 can bring both indoors. A G51 on the same site brings one.
| Your site | Why the G41 fits |
|---|---|
| No 3.5 GHz 5G at the donor antenna, which is common outside the cities and larger towns | Two 4G channels of up to 20 MHz each. A G51 without n78 relays one |
| You are on Vodafone and its 700 MHz signal is the one that reaches you | Only the G41-NE covers band 28U. The G51-LE and R41-YB cover 28L |
| Your carrier's 2,300 MHz band (band 40) is in use at the site | The G41-JE and G41-NE list band 40. The G51-LE does not |
| You want the fixed unit Telstra itself sells | Telstra's device page listed the GO G41 for buildings, and no G51, on 14 November 2026 |
| The unit runs from solar, a battery or a UPS | 30 W maximum (21 W typical) against 60 W maximum for the G51 |
| Space on the wall is tight | 1.0 kg on a 267 x 107 mm footprint against 2.2 kg on 265 x 172 mm |
Choose the G51 when a 5G phone on your carrier shows the 3.5 GHz band at the donor position and you want that speed indoors. It is the only one of the three that relays band n78, and it does so at 27 dBm, five times the power of its 4G channel, which helps at a frequency that loses more in walls and cable. The 5G icon alone does not prove band n78: carriers also run 5G in lower bands, and the G41 handles those where the channel sits in a band it supports (its datasheet lists 5G NR in both NSA and SA forms). If you cannot tell which band the phone is on, ask us for a desktop study before you choose.
One detail for installers: the G41's ordering table lists bands 1 and 3 as the "dual relay bands" of the JE and NE kits, and the earlier datasheet says the unit supports more than one channel per band in those bands. We read that as: the two channels can sit in two different bands, or both in band 1 or both in band 3.
The two share the same IntelliBoost chip generation and the same 100 dB of gain, and the R41 is the smaller unit, so the question comes up often. They are built for opposite jobs.
| GO G41 | ROAM R41 | |
|---|---|---|
| Built for | Buildings. Telstra sells it as its stationary repeater | Vehicles and boats. Telstra sells it as its mobile repeater |
| Channels relayed at once | 2, each up to 20 MHz | 1, up to 20 MHz |
| Downlink output power | 20 dBm (100 mW) | 0 dBm (1 mW) |
| Uplink output power | 20 to 22 dBm | 22 to 24 dBm |
| Bands the other lacks | Band 40, and 28U in the NE kit | Band 26 |
| Power | 12 V DC from its AC adapter (11.4 to 12.6 V at the unit), 30 W max. | 11.5 to 15 V DC from a vehicle socket, 18 W max. |
| Operating temperature | 0 to 40 °C | 0 to 60 °C |
| Setup and monitoring | Bluetooth, plus Ethernet for remote monitoring | Bluetooth only |
| Installation | Professional installation recommended by Telstra | Made for self-installation |
The downlink row is the whole difference in coverage. 20 dB is a factor of 100 in power: the G41 has enough to feed ceiling antennas across a building, and the R41 has enough to fill a cabin from a small antenna near the driver. The uplink row runs the other way, so the path back to the tower is what an R41 improves most.
The power row cuts both ways too. The G41's 11.4 to 12.6 V input is narrower than the 13.8 to 14.4 V a vehicle battery sees while charging, so the fixed unit is not one to wire to a vehicle, and the R41's 11.5 to 15 V input is made for exactly that.
It can cover a small one. Nextivity describes the R41 for cars, trucks, RVs and boats, and Telstra sells it as a mobile repeater. Its output power is low compared with the in-building units, and with an AC power supply it can give spot coverage in one room. So a caravan annexe, a site hut, a market stall, a boat deck or the area around a parked work vehicle is within its reach. A house, a shed or a yard is G41 work.
Antenna. For an area outside the cabin, replace the small cabin antenna with a directional panel aimed across the area you want covered. The RFI CPL6938 has a fitted 10 m lead with an SMA male plug that screws straight onto the R41. The RFI DAS6938-SDP150-N is IP55 rated with an N female tail, so it needs an SMA male to N male lead. A panel concentrates the R41's 1 mW in one direction (the DAS6938-SDP150-N's datasheet gives 5 to 7 dBi by band), which is how to get the most from it. Point the panel away from the donor antenna and keep the vehicle or a wall between the two.
Where the unit goes. The R41 is rated IPX0, the same as the indoor units, and to 60 °C. Only the antennas and sealed connectors go outside. The unit stays in the cabin, the van, the hut, or a weatherproof enclosure that stays under 60 °C inside.
Power. The R41 takes 11.5 to 15 V DC and draws up to 18 W, 1.5 A. Its quick start guide is blunt: "This device can ONLY be connected with 12V auxiliary power outlet", and the kit's lead ends in a fused accessory plug. That leaves three practical arrangements:
At the 18 W maximum the unit uses 432 Wh in 24 hours, about 36 Ah from a 12 V battery, which is the figure to size a battery or solar panel against. For mains power in one room, use an AC power supply made for the R41 instead of adapting a plug pack, because Nextivity's own guide names only the 12 V outlet. A spare 12 V power lead for the R41 is on the Store.
What to expect. The R41 puts out 1 mW where a G41 puts out 100 mW. In open space 20 dB is a factor of ten in distance, so with the same antenna an R41 holds a given signal level at about one tenth of the range of a G41. That is free-space arithmetic, not a coverage promise, but it explains why one room is the realistic limit.
Permission. The carrier's written permission covers the use you describe to it. Telstra's device page places the R41 in cars and other vehicles, boats and caravans, and the G41 in buildings: homes, offices and businesses. Tell the carrier what you plan and get its answer in writing. For a fixed site that needs coverage outdoors, such as a loading dock or a yard, the better design is a G41 or G51 indoors feeding an outdoor-rated panel, described in the installation guide under antenna layouts.
The Store's ROAM R41 packs pair the unit with an RFI donor antenna chosen in the listing, and every pack has the small RFI T5 for the cabin. The RFI vehicle antennas come in three families and three gains. CD antennas have a fixed whip on a spring base. CDR and CDQ antennas have RFI's Q-Fit whip, which unscrews from the base for car parks, car washes and security. The number gives the gain: 8194 is 5.5 dBi, 8195 is 6.5 dBi and 8197 is 7.5 dBi, and the whip grows with it, from about 0.65 m to about 1.2 m.
| Vehicle or vessel | Pack antenna | Why |
|---|---|---|
| Car, SUV or van used in town and in hills | CD8194-B, CDR8194-B or CDQ8194-B, 5.5 dBi | The shortest whip, with the broadest vertical pattern for uneven country |
| 4WD, touring ute or tow vehicle on mixed roads | CD8195-B, CDR8195-B or CDQ8195-B, 6.5 dBi | The all-round choice for a bull bar |
| Truck or long-distance vehicle on flat, open country | CD8197-B or CDQ8197-B, 7.5 dBi | The most gain towards the horizon, on the tallest whip |
| Ambulance, service van or fleet car that cannot carry a whip | RFI CSM700 compact antenna | A low-profile stud-mount antenna for the roof |
| Boat | CDQ8195 marine antenna | The 6.5 dBi whip in its marine version, fitted high on the superstructure |
| Vehicle that already has a suitable antenna with an SMA lead | "Without external antenna" | The unit, the cabin antenna and the power lead only |
Higher gain is not always better on a vehicle. A high-gain whip squeezes its pattern towards the horizon, which suits flat country and suffers in hills, where the tower may sit well above or below the vehicle. If the vehicle does both, take the 6.5 dBi antenna. How to fit the antennas and the unit in a car, a 4WD, a truck or a boat is in the installation guide under installing a ROAM R41.
| Site | Unit | Why |
|---|---|---|
| Farmhouse or homestead, one carrier, 4G outside but not inside | GO G41, JE or NE to match the carrier | Two 4G channels and 20 dBm downlink; LPDA on the roof, CNT-400 cable, dome or panel inside |
| Shed, workshop, small office or shop where phones show 3.5 GHz 5G outside | GO G51 with the mini LPDA | The only one that relays band n78, with a 100 MHz channel at 27 dBm |
| The same building, but no 3.5 GHz 5G at the roof | GO G41 | The G51 would relay a single 4G channel there |
| Ute, truck, 4WD, boat or the tow vehicle of a caravan | ROAM R41 | 12 V, 18 W; bull-bar or roof donor antenna, small antenna in the cabin |
| Caravan annexe, site hut or stall beside a vehicle | ROAM R41 with a panel antenna | Small-area coverage from a 12 V supply |
| Shop floor plus a loading dock or yard | GO G41 or G51, a two-way splitter, one ceiling dome and one IP55 panel | Both areas from one unit |
| Site where staff are on two carriers | Two units, one per carrier, sharing the indoor antennas through a hybrid combiner | Each unit serves one carrier at a time |
| Site with no usable signal anywhere outside | None of them | A repeater re-radiates what it receives; the system needs at least one bar somewhere outside |
| Building of more than two or three floors | Cel-Fi QUATRA | One Network Unit feeds a Coverage Unit on each floor over category cable; ask us |
Two carriers. A GO serves one carrier at a time, so a site that needs Telstra and Optus needs two units, each with its own carrier's permission. They do not need two sets of indoor antennas: a hybrid combiner joins the two units to one set of server antennas, at a cost of about 3 dB each. The donor side is usually two antennas, each aimed at its own carrier's tower. The parts and the losses are in the installation guide under two carriers on one site.
Several floors. One GO split across many floors runs out of power quickly: every doubling of the number of antennas costs each of them a little over 3 dB before any cable loss. Two or three floors can share a unit or have one each. For a building of ten floors, or several buildings on one site, the right product is Nextivity's QUATRA, an active system that puts a powered Coverage Unit on each floor, fed over category cable instead of coax. The comparison is in the installation guide under several floors. QUATRA systems are scoped per building, so ask us.
| Job | Unit and pack | Donor antenna | Cable and connectors | Server side |
|---|---|---|---|---|
| House or small office, one or two rooms, runs up to 15 m, 4G | G41 "LPDA + Dome" or "LPDA + Panel" pack: JE for Telstra and Optus, NE for Vodafone | LPDA in the pack | The pack's 10 m and 15 m CNT-400 leads and SMA to N adaptors | The pack's ceiling dome or wall panel |
| Shed, workshop or shop that sees 3.5 GHz 5G | G51 "Mini-LPDA + Dome" or "Mini-LPDA + Panel" pack | Mini LPDA in the pack, for its gain on band n78 | The pack's CNT-400 leads; keep the runs as short as the building allows | The pack's dome or panel; add a two-way Wilkinson and a second antenna for a long building |
| Large house, long shed or small warehouse, runs of 15 to 25 m, two server antennas | G41 or G51, unit only | LPDA7038 with N female tail for a G41, LPDA7040 for a G51 | CNT-400 by the metre with N-201 connectors, or 20 m leads; SMA to N leads at the unit | Two-way Wilkinson, two domes or panels |
| Warehouse or packing shed, or a donor mast away from the building; runs over 25 m; up to four antennas | G41 or G51, unit only | LPDA, or the YW15-6989 Yagi for a weak low-band signal on a G41 | LDF4-50A with L4TNM-PSA connectors; short SMA to N leads at the unit | Four-way split, domes or panels by zone |
| Office or shop where staff are on two carriers | Two GO units, one set to each carrier | Two LPDAs, each aimed at its own carrier's tower | As the rows above, for each unit | A 2x2 hybrid combiner, then two domes or panels |
| Ute, truck, 4WD, boat or caravan tow vehicle | ROAM R41 pack with the RFI antenna that suits the vehicle | Bull-bar or roof antenna in the pack | Leads supplied with the antennas | The pack's RFI T5 cabin antenna |
Bigger than the last fixed row, or more than one floor of offices: ask us about a QUATRA system instead of stretching a GO.
A fixed Cel-Fi GO system has a donor antenna outside, aimed at the carrier's base station; the unit indoors; one or more server antennas where coverage is needed; and low-loss coaxial cable between them. Six things make or break it:

Each of these has its own section, with tables, loss figures and worked designs, in the Cel-Fi installation guide.
A mobile phone booster is an amplifier that connects physically to a handset and boosts what it transmits to the base station. The Telecommunications (Prohibition of Mobile Phone Boosters) Declaration 2021 prohibits operating one, supplying one, or possessing one for either purpose, on the ground that boosters can interfere with the public mobile networks.
A cellular mobile repeater is a different device. The Declaration defines it as equipment that receives the base station's signal and retransmits it to handsets, and does the same in reverse, and states that a repeater is not a booster.
A repeater is still a transmitter on the carrier's frequencies. The ACMA's cellular mobile repeaters page allows two routes: the model is an exempt repeater, or the carrier has given its permission under its own licence, which the ACMA calls a "third-party agreement". The mobile bands are licensed to the carriers, not to you, so a repeater on Telstra's channels operates under Telstra's licence and Telstra has to agree. The ACMA adds that carriers authorise only a small range of models.
An exempt repeater is one the ACMA has declared exempt, on a carrier's application, under the Radiocommunications Equipment (General) Rules 2021, and the ACMA publishes them in its list of exempt repeaters. Cel-Fi models are on that list, which is what makes them lawful to supply in Australia. The exemption lets a supplier sell the model. It does not let you run it: the ACMA's permission page says "You must have written permission from a telco to use a mobile repeater", exempt models included. The penalties on that page are a maximum of A$412,500 and/or two years in prison for using an unauthorised repeater, fines up to A$137,500 for supplying one to an unlicensed person, and a maximum of A$1,650,000 or five years in prison for significant interference.
For a buyer that means three steps: buy a model your carrier accepts, get its permission in writing, and set the unit to that carrier in the manufacturer's app.
Cel-Fi is made by Nextivity, whose Australia page claims that "Nextivity makes the only legal repeaters in Australia" and shows the Telstra, Optus and Vodafone logos. The page lists four products for Australia, the QUATRA 4000e for large buildings, the ROAM R41, the GO G41 and the GO G51, and advises one unit per carrier.
Telstra is the carrier we could verify directly. Its coverage extension devices page, read on 14 November 2026, sells the Telstra GO G41 Stationary Repeater for buildings and the Telstra GO ROAM R41 Mobile Repeater for vehicles, vessels and caravans, and recommends professional installation, for stationary units especially. Telstra's 2018 announcement says its GO repeaters were "tested, authorised and approved by Telstra", and its terms say Telstra "must authorise you to operate it", that a unit is pre-qualified for a location, and that you must tell Telstra if you move it to another address. The GO G51 was not on Telstra's device page on that date.
For Optus and Vodafone we could not find a public page on either carrier's site naming approved repeater models. The ACMA's list of exempt repeaters is the public record: it gives the brand, the model, the carrier that asked for the exemption and the date, so check the exact model you are buying against it. The ACMA's rule settles the practical question: ask your carrier in writing, before you buy, whether it will authorise the exact model for your address or vehicle.
"Cel-Fi GO Smart" is a description, not a model. Nextivity's GO page names the G41 a "Single-Carrier 3G/4G/5G Smart Signal Booster" and the G51 in similar words, and Nextivity's product list has no GO Smart. What people often mean is the older, smaller GO G31 or G32, which switched between a stationary and a mobile mode. Nextivity's G32 page says it is no longer manufactured and names the GO G41 and ROAM R41 as its replacements.
No. The Telecommunications (Prohibition of Mobile Phone Boosters) Declaration 2021 prohibits operating, supplying or possessing a mobile phone booster, meaning equipment that connects physically to a handset and amplifies its transmissions. A cellular mobile repeater is excluded from that definition and is legal only with the written permission of the carrier whose network it uses, even for a model on the ACMA's exempt list.
Not one of your own. The repeater transmits on the carrier's licensed frequencies under what the ACMA calls a third-party agreement, so the document you need is the carrier's written permission for that model at that address or in that vehicle.
Only where the carrier's 3.5 GHz 5G (band n78) reaches your donor antenna. The G51 relays one n78 channel up to 100 MHz wide plus one 4G channel up to 20 MHz. The G41 relays two 4G channels up to 20 MHz each. Without n78 at the site, the G41 carries twice the 4G spectrum of the G51.
One at a time. You choose the carrier in the WAVE App and can change it later, subject to that carrier's permission. For 700 MHz on Vodafone you need the G41-NE variant; the G41-JE, G51-LE and R41-YB cover the lower 700 MHz block only.
For a small area, yes. Its downlink is 0 dBm, one hundredth of a G41's, so it gives spot coverage for one room. The unit is not weatherproof, runs from 11.5 to 15 V DC, and is sold by Telstra as a mobile repeater, so check with your carrier before using it at a fixed site. For a building or a yard, use a G41 or G51.
Go by the length of the run. The rule of thumb is a low-loss RG58-size cable such as 9006 under about 10 m, CNT-400 from 10 to 25 m, and 1/2 inch LDF4-50A beyond 25 m. For a G51 on band n78, move up one cable size earlier: at 3,600 MHz a 15 m run loses 4.1 dB in CNT-400 and 2.2 dB in LDF4-50A.
Yes, through a splitter, when the unit is producing enough power. Nextivity's G51 guide asks for a downlink above 0 dBm for a two-way splitter and above 3 dBm for a four-way, and for more than 20 dB of isolation between splitter ports. A two-way split costs each antenna up to 3.6 dB and a four-way up to 6.9 dB.
No. Each GO or ROAM unit serves one carrier at a time. Two carriers need two units, which can share one set of indoor antennas through a hybrid combiner. Larger buildings can use a QUATRA system, which Nextivity makes in one-carrier, two-carrier and multi-carrier versions.
Two or three floors can be covered by a GO, either one unit split between floors or one unit per floor. Beyond that, splitter loss and riser cable leave too little power on each floor, and a QUATRA system is the better design: a powered Coverage Unit on each floor, fed over category cable from a central Network Unit.
Yes. After installation the unit is registered through the Nextivity WAVE App before it goes into service. Nextivity also releases software updates, and some of them are essential to the way the unit works, so apply each one when it is offered.
Nextivity's current datasheets give no floor area. An earlier G41 datasheet quoted up to 3,000 m² per system, and a fair planning figure for the coverage radius is about 20 m through timber-framed walls and more than 65 m in open commercial space. The real figure depends on the signal at the donor antenna, the building and the server antennas. A ROAM R41 covers a vehicle cabin.
A ROAM R41 runs from the 12 V socket, but its donor antenna, cabin antenna and ground cable are fixed to the vehicle, so moving it means fitting antennas in the second vehicle. For a fixed unit, Telstra's terms require you to tell Telstra if you move it to a different address, so check your carrier's authorisation before relocating either type.
Not a model. Nextivity describes the GO units as smart signal boosters, and the phrase has stuck to the line. The small GO G31 or G32 that switched between building and vehicle modes is no longer manufactured; the GO G41 and the ROAM R41 are its replacements.
The Techwave Store carries the Cel-Fi GO G41 packs for Telstra and Optus, the G41 packs for Vodafone, the Cel-Fi GO G51 packs and the Cel-Fi ROAM R41 with RFI antennas, together with the donor and server antennas, the CNT-400 and LDF4-50A cable, and the Pulse and CommScope connectors named in this guide. The full range is in the Cel-Fi collection. Tell us the carrier, the site and the signal your phone shows at the roof, and we will match the variant, the antennas, the cable and the splitter, and remind you to get the carrier's written permission before the unit is switched on.
The manufacturer pages, datasheets and carrier pages linked in this article were read on 1, 8 and 14 November 2026. Specifications and carrier device lists change, so check the current datasheet and your carrier before you order.